Select your country
Prices Inc.Tax Excl.Tax

Axial fans

Axial fans

AW sileo / AW sileo EC

AW sileo / AW sileo EC

AW fans are designed for wall mounting using a square base. Axial wall AW fans are equipped with axial impellers and external rotor motors. The housing is made of galvanized steel and are powder-coated in black. Axial impellers with vanes are made of aluminum alloy and is also painted in black. Rotational speed axial fans wall AW can be continuously controlled. All motors are equipped with thermal contacts on a terminal block fan, which must be connected to the corresponding relay thermal protection. Axial wall fans AW can be mounted in any position.

 

HXBR / HXTR

HXBR / HXTR

Axial fans HXBR/HXTR are suitable for ventilation directly through the wall. Fans HXBR/HXTR are suitable for industrial applications for ventilation of buildings, businesses, stores, etc. Fans type HXBR/HXTR axial fans are designed for wall mounting. The new range of axial fans wall sickle blades with diameters from 250 mm to 1000 mm. Models are available with single-phase or three-phase motors in versions with 2, 4, 6, 8 and 12 poles. The range of air flow is from 930 to 26,000 m3/hour. They are intended to transport air without mechanical particles that could cause abrasion or imbalance of the impeller. Fans HXBR/HXTR are designed for non-explosive areas, must not be exposed to direct effects of the weather. It can be installed in a horizontal or vertical position. All single-phase fans except HXBR/4-560, /4-630 and /6-710 may be controlled transformer or electronic speed controllers. The three-phase fans can be controlled up to the transformer regulators HXTR/4-560, /4-630 and models from 710 to 1000. Models of 800-1000 can adjust the recommended frequency converter. Fans should be stored in covered and dry warehouse.

 

HCFB / HCFT

HCFB / HCFT

Fans type HCFB/HCFT axial fans are applicable for wall mounting. The fans are suitable for air-conditioning and industrial applications, which is preferably applied low noise and high flow air fan. Axial wall fans HCFB/HCFT can be installed in a horizontal or vertical position. They are intended to transport air without mechanical particles, that could cause abrasion or imbalance of the impeller. Fans HCFB/HCFT are designed for non-explosive areas, must not be exposed to direct effects of the weather. Most of the fans of this series can be controlled transformer or electronic speed controllers. Wall fans type HC xx H are designed to exhaust air to the outside, fans for supply are labeled HB. Fans should be stored in covered and dry warehouse. Fans are manufactured under the strictest production control system to ISO 9001.

 

HCBB / HCBT

HCBB / HCBT

Fans type HCBB/HCBT axial fans are applicable for wall mounting. The fans are suitable for air-conditioning and industrial applications, which is preferably applied low noise and high flow air fan. Axial wall fans HCBB/HCBT can be installed in a horizontal or vertical position. They are equipped with an impeller made of aluminum alloy. Complemented by a series of axial fans HCFB, HCFT, HCGB, HCGT. They are intended to transport air without mechanical particles that could cause abrasion or imbalance of the impeller. Axial wall fans HCBB/HCBT are intended for non-explosive areas. Fans that have the following table of technical data mentioned type of controller can be controlled transformer speed controllers. Fans who are not given the type of controller, can not be controlled. Fans are manufactured under the strictest production control system to ISO 9001.

 

HXM

HXM

Axial wall fans HXM are suitable for less demanding applications in industry and agriculture. Fans HXM are for ventilation through the wall. Type fan HXM are axial for mounting on the wall. They are to transport air without mechanical particles, which could cause abrasion or imbalance the impeller. Fans are for space where is not dangerous of explosion, should not be direct to effect of the weather. Fans can be controlled via transformer or electronic speed controller reduce of the voltage.

 

TXBR / TXTR

TXBR / TXTR

Axial fans HXBR/HXBR are suitable for short air with low pressure loss and are installed directly into the duct. Fans TXBR/TXTR are suitable for industrial applications for ventilation of buildings, businesses, stores, etc. Fans type TXBR/TXTR axial fans are designed for installation in duct. The new range of axial duct fans with sickle-shaped blades in diameters from 250 mm to 1000 mm. Models are available with single-phase or three-phase motors in versions with 2, 4, 6, 8 and 12 poles. The range of air flow is from 930 to 26,000 m3/hour. They are intended to transport air without mechanical particles that could cause abrasion or imbalance of the impeller. Fans TXBR/TXTR are designed for non-explosive areas must not be exposed to direct effects of the weather. It can be installed in a horizontal or vertical position. All single-phase fans except TXBR/4-560, /4-630 and /6-710 may be controlled transformer or electronic speed controllers. The three-phase fans can be controlled up to the transformer regulators TXTR/4-560, /4-630 and models from 710 to 1000. Models of 800-1000 can adjust the recommended frequency converter. Fans should be stored in covered and dry warehouse.

 

TCBB / TCBT

TCBB / TCBT

Fans type TCBB/TCBT axial fans are designed for installation in circular ducts. Fans TCBB/TCBT are fans with high performance and in terms of development in the duct network in a convenient short cabinets. Fans can be installed in a horizontal or vertical position. They are equipped with an impeller made of aluminum alloy. Replace a range of duct fans TCFB, TCFT, TCGB, TCGT. They are intended to transport air without mechanical particles, that could cause abrasion or imbalance of the impeller. The fans are designed for non-explosive areas. Fans that have the following table of technical data mentioned type of controller can be controlled transformer or electronic speed controllers. Fans, who are not given the type of controller, can not be controlled. The three-phase fans can be controlled transformer controllers or by frequency converters. Fans are manufactured under the strictest production control system to ISO 9001.

 

AR / AR sileo

AR / AR sileo

Axial fans AR Sileo are fitted with bionic shaped blades are driven by external rotor motors. Fans AR Sileo designed for installation in circular ducts are fitted with flanges according Eurovent 1/2. The housing is made of galvanized sheet steel powder-coated black (RAL 9005). Protective grille on the intake also has a powder coated black. Axial fan impeller AR force is made of composite material is black and dynamically balanced at two levels in accordance with DIN ISO 1940 part 1, quality G6.3. Fan speed can be infinitely controlled thyristor 2-st. switch (400V only) or 5-st. transformer. All motors are equipped with thermal contacts on a terminal block fan, which must be connected to the corresponding relay thermal protection.

 

TRB / TREB

TRB / TREB

Fans TRB/TREB are suitable for short air with low pressure loss.Fans are primarily intended for installation in pipes or for walling and exhaust directly through the wall. Bipolar embodiment axial duct fans TRB/TREB is suitable for ducts with a relatively large pressure drop. Duct axial fan series TRB, for example, are designed for installation into the circular duct without flanges and are available in four nominal diameters of 200, 250, 300 and 350 mm. Series fans are designed for installation in normal or flexible system air duct. Flow fan power TRB, for example ranging from 450 to 3,070 m3/h. Fans of the series are available in two versions. All models are supplied with single-phase motors with external rotors of the two-pole (models 200 and 250 mm) and four-pole versions. Covers series fans TRB - TREB are made from rolled sheet of stainless steel, coated with tough black polyester paint. TRB models are equipped with a robust extra holder welded to the fan housing. The flow direction B, i.e. from the impeller to the motor. - Models TRB - Direction of flow type, ie. From the motor to the impeller. The fans of the PDP, such are intended to convey air without mechanical particles that could cause abrasion or imbalance of the impeller. The fans are designed for non-explosive areas, must not be exposed to direct effects of the weather. It can be installed in a horizontal or vertical position. Fans can be controlled transformer or electronic speed controllers. Fans should be stored in covered and dry warehouse.

 

AXC

AXCAXC medium-pressure axial fans are manufactured from a diameter of 315 to 2000 mm (315 to 500 AXCP - optimized blade AXC fans, AXCPV AXC fans with optimized blades and bumpers on the displacement side). AXC fans, thanks to a large selection of motors, blade angle settings, number of poles, flow direction, etc., can be tailored to your specific work point requirements. Fans are equipped with PTC thermistors that protect motors. Fans are fitted with Eurovent 1/2 flanges. AXC fans are only on demand and are manufactured to order according to your individual requirements and needs. If you are interested in any of these fans please send a request to our e-mail with the required working point of the fan, contact us by phone.
 

AXCBF

AXCBF

AXCBF the axial middle fans with separate air stream, have been developed for such industrial applications where it would normally be necessary proposal special resistant engines or where the life of a standard motor in the given conditions is substantially reduced. AXCBF fans are therefore suitable for the gaseous fluid with aggressive properties or for permanent outlet air temperatures up to + 200°C.

 

TGT

TGT

Fans TGT and CGT the duct axial fans with adjustable pitch angle of the blades. All basic models are available with three-phase motors in the four and six-pole versions. Flow transported air ranges from 10.000 to 120.000 m3/h. The direction of air flow from the impeller to the motor. Sheath fans TGT flanged circular duct is made of a rolled sheet of stainless steel, coated electroplating. CGT fans are equipped with noise-insulated casing made of galvanized sheet metal flanges for square pipe. Models series fans TGT and CGT are available with impeller with 3, 6 or 9 blades with adjustable pitch angle. (Must be ordered in production). The complete impeller assembly allows an accurate choice of flow and pressure. All impellers are made by pressure casting from high quality aluminum alloy. Fan motors can be controlled. They are intended for air at 70°C.

 

TCBB / TCBTx2

TCBB / TCBTx2

Fans type TCBBx2 and TCBTx2 medium pressure axial fans are designed for installation in circular ducts. They are equipped with two drive units with impellers of aluminum alloy in opposite design. Impellers fans are specially optimized and can not be confused impellers fans TCB series. They are designed for non-explosive areas and can be installed in a horizontal or vertical position. The fans for which it is given the possibility of regulation, it is possible to regulate the transformer speed controllers. Fans with no controller type listed, it is not possible to regulate.

 

CGT

CGT
 

ZAplus

ZAplus

Axial fans ZAplus with AC motors and ZAplus-ECblue with EC motors. Fans are widely used in various industries, mainly used in refrigeration systems, and air conditioning units. They are further used for engineering, manufacturing, agriculture, mass transport, boats, recuperation units and many others.

ZAplus fans are available as standard in sizes 450 - 910 mm with flow rates up to 36,500 m3/h and static pressure up to 420 Pa. The fans are characterized by low operating costs and very low noise thanks to bionic blade design and optimized ZAplus nozzle. The Fans are also very employed for the possibility of the rotation speed control. For ZAplus fans it is possible to increase their air output with the ZAplus + diffuser. Fans have sinuous profiled blades made of composite material or aluminum for better air performance and lower noise.

Many accessories are supplied to the fans: self-closing shutter, guard grille, mounting kits,

The fans are very flexible due to the large number of motors, the number of poles, the setting of blade angles, the possibilities of determination, the various mounting possibilities and the many accessories.

Fans meet the ErP 2015 directive and have many other certifications.

 

FFowlet

FFowlet

FFowlet axial fans with AC motors, FFowlet-ECblue with EC motors are fans designed primarily for the agricultural industry. Fans are widely used in various industries, used for ventilation and ventilation, cooling / air conditioning units, agriculture and many others. For the FFowlet fans, add a ZAplus nozzle as an accessory to improve the airflow of the fan.

FFowlet fans are available as standard in sizes 500 - 910 mm with flow rates of up to 24,500 m3 / h and static pressure up to 150 Pa. The fans are specially designed to operate at low pressure losses. Fans have sinuous profiled blades, thanks to which fans deliver better air performance and lower noise. Fans are also very useful for speed control. The fans are equipped with an IP 55 protection class and the blades have a surface finish for extreme conditions.

A lot of accessories are supplied to the fans: self-closing shutter, protective grille, mounting kits,

The fans are very flexible due to the large number of motors, the number of poles, the setting of blade angles, the possibilities of determination, the various mounting possibilities and the many accessories.

 

FE2owlet

FE2owlet

Axiální ventilátory FE2owlet s AC motory, FE2owlet-ECblue s EC motory a FE2owlet-ECQ jsou ventilátory určené pro chlazení. Ventilátory mají široké využití v různých odvětvích, využívají se pro strojírenství, výrobní průmysl, chladící/klimatizační jednotky, v zemědělství, ve vozidlech hromadné dopravy, na lodích, v rekuperačních jednotkách a mnoho dalších.

Ventilátory FE2owlet se standardně dodávají ve velikostech 250 – 1250 mm s objemovými průtoky až 53 000 m3/h a statickým tlakem až 418 Pa. Ventilátory se vyznačují nízkými náklady na provoz a minimální hlučností. Ventilátory mají srpovité profilované lopatky vyrobené z kompozitního materiálu nebo hliníku k docílení lepších vzduchových výkonů a nižšího hluku. Ventilátory mají velké využití také díky možnosti regulace otáček.

K ventilátorům se dodává velká spousta příslušenství: samočinná uzavírací klapka, ochranná mřížka, montážní sady atd.

Ventilátory jsou velice flexibilní díky velkému množství motorů, počtu pólů, nastavení úhlů lopatek, možnostem určení, různým montážním možnostem a díky spoustě příslušenství.

Ventilátory splňují směrnici ErP 2015 a mají mnoho jiných certifikací.

 

FB

FB

Axial fans FB are only produced with AC motors. The main uses are in the refrigeration and air-conditioning units and in heating. They will also find use in mechanical engineering and the automotive industry.

Axial FB fans are available in sizes from 200 to 630 mm for volume flow rates up to 12 500 m3/h and static pressure up to 159 Pa. Fans have metal blades for use in a short jet. Fans can also be used for explosive ATEX environments.

 

FC

FC

Axial fans FC are manufactured with AC motors only. Fans are widely used in various industries, used for engineering, manufacturing, refrigeration / air conditioning, agriculture, public transport vehicles, boats, recuperation units and many others.

FC fans are available in sizes 315 - 1250 mm with a flow rate of up to 62,000 m3/h and a static pressure of up to 300 Pa. Fans have shaped aluminum die casting blades that are used to guide air in aerodynamically well-designed systems.

The fans are very flexible due to the large number of motors, the number of poles, the setting of blade angles, the possibilities of determination, the various mounting possibilities and the many accessories.

Fans meet the ErP 2015 directive and have many other certifications.

If you are interested in any of these fans, please send a request info@ventilatory.net with the desired working point of the fan.

 

AJR / AJ8

AJR / AJ8

Jet fans AJR and AJ8 offers the highest performance of the ventilation system at low installation and operating costs. They are available in sizes 315, 355 and 400 mm. The system allows normal operating and fire ventilation. For straight airflow the silencers have integrated inlet cones and guide vanes. The sound attenuating material is non-flammable according to DIN 4102, corresponding with EU guideline 97/69. Deflectors on the outlet side are available as an accessory.

 

TET

TET

Fans type axial fans TET are suitable for special applications. Fans cabinet is made of steel, galvanized steel sheet and painted gray epoxy paint. The impeller is cast from Al alloy. The engine is mounted outside the air stream in the guide channel through the fan housing. The fans are designed to transport air without mechanical particles that could cause abrasion or imbalance in the fan impeller. Axial fans TET is designed for non-explosive areas must not be exposed to direct effects of the weather. They are intended for transportation of air at 150°C.

 

PBB / PBT

PBB / PBT

Fans type PB, PBT are axial fans in special designs. They are intended to transport air without mechanical particles that could cause abrasion or imbalance of the impeller. Fans PBB, PBT is designed for non-explosive areas, must not be exposed to direct effects of the weather. Fans are equipped with a stand that allows their position and location in the space, switch and protective grilles. The fans are designed for ventilation of production shops, foundries, drying rooms, engine rooms, buildings, greenhouses and the like. The fans can be controlled transformer speed controllers.

 

TTT

TTT
 

TBT

TBT

Fans TBT of the duct medium pressure axial fans are available in two sizes, 400 and 450 mm. Both basic types of fans are available with three-phase motors. Flow transported air ranges from 9,300 to 13,200 m3/hour. TBT fans are suitable for duct systems in industrial applications with large pressure loss. Fan nozzle with the flange is made of a rolled sheet of stainless steel coated with epoxy paint - polyester paint gray color. Impellers are made by pressure casting from high quality aluminum alloy and are provided with epoxy paint red. The fans are designed for non-explosive areas; should not be exposed to direct effects of the weather. The fans are designed to transport air without mechanical particles that could cause abrasion or imbalance of the impeller. Fans should be stored in covered and dry warehouse.

 

HIB / HIT

HIB / HIT

Fans HIB.HIT are axial with housing made of galvanized steel sheet. Fan housing is equipped on the first side safety grid and on the second side with louvre. Direction of air flow is from safety grid to louvre. Motors HIB,HIT cannot be controlled. Fans are for non-explosion areas, should not be exposed to direct effects of the weather. They are for use in construction, agriculture for transport air to 40°C. Fans should be stored in covered and dry warehouse.

 

TURBO

TURBO

TURBO fans are axial fans with a special finish. The fan is made of electroplated circular profiles. It is mounted on a frame of steel tubes and fitted with a protective grid. The casing can after loosening the nut to film as required. TURBO type fans are designed to transport air without mechanical particles that could cause abrasion or imbalance of the impeller. The fans are designed for non-explosive areas must not be exposed to direct effects of the weather. TURBO fans are designed for ventilation of production shops, foundries, drying rooms, engine rooms, buildings, greenhouses and the like. The fans can be regulated two-stage speed regulator, which is supplied.